SERIBOND-SBFI SERIBOND-SBFI is excellent for burst fastness improvement for paper Industry used with starch at side press. It is most suitable product for short fiber pulp like Bagasse, Straw, Waste paper, Bamboo, hard wood etc. It also improves strength properties like burst factor, stiffness, breaking length, ply bonding, tear factor of Kraft, Duplex Board and writing and printing paper, SERIBOND-SBFI gives better sheet formation and also increase machine run ability. It improves retention of fillers & fines and eliminate press picking problem of paper. Specification Appearance: Clear Water Colour Solid: 20 ± 1 Viscosity on Brook Field cps: 3000-6000 PH Value: 4 ± 1 Ionic nature: High Anionic Composition: Acrylic based fiber bonding agent Solubility: Easily soluble in water Shelf Life: 180 days Application SERIBOND-SBFI can be used in all kinds of writing & printing paper, Duplex boards, Kraft paper ect. It may be used after addition of rosin and best addition point is size press The recommended dosage of SERIBOND-SBFI is 0.20% to 0.60% on dry paper basis to get the desired result. Packing: 200 Kgs Carboys and 200 Kgs. Drums Storage & Handling: Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND–3030 (WSR) SERIBOND–3030 (WSR) resin is a unique chemistry. This versatile product is specially designed to perform critical tasks in towel, napkin and facial grades. Promotion or improved retention of polyamide wet strength resin Enhancement of Functional performance of the sheet with higher wet strength, dry strength, and improved Wet-Over-Dry Restoring Wet End Charge Balance, especially on machines that run close to or in the cationic range Specification Appearance: Liquid, clear to slightly hazy Solid: 30 + 2 % Density: 1.05 g/cm3 Viscosity @ 250C: 2,300 – 6,300 cps PH Value: 3 + 0.5 Ionic nature: cationic Solubility: Easily soluble in water Application SERIBOND–3030 (WSR) resin is designed to be added after the polyamide wet strength resin at a point of good mixing. It is important that the SERIBOND–3030 (WSR) resin is thoroughly mixed with the stock. Addition of SERIBOND– 3030 (WSR) to either the thin or thick stock is acceptable, depending upon the polyamide wet strength resin and other cationic additives dosage points and program objective. Typical dosage level for the SERIBOND–3030 (WSR) is 10 to 20 kgs per ton (1 to 2 %) on fiber, dry solids basis. Packing:200 Kgs Drums Storage & Handling:Storage must be in covered place. Carboys should be kepttightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND-FILLEX SERIBOND-FILLEX is two component cross linking bonding system which provide excellent dry strength resin for paper Industry. It is most suitable product for short fiber pulp like Bagasse, Straw, Waste paper, Bamboo, hard wood etc. It also improves strength properties like burst factor, stiffness, breaking length, RCT, ply bonding, tear factor of Kraft, Duplex Board and writing and printing paper, SERIBOND FILLEX gives better sheet formation and also increase machine run ability. It improves retention of fillers & fines and eliminate press picking problem of paper. Specification: Part A || Part B Appearance: Hazy to clear liquid || Clear viscously Solid: 14 ± 1 || 14 ± 1 PH Value: 5.1 ± 0.1 || 4 ± 1 Ionic nature: Cationic || Mildly cationic Composition: Bond system || Hardener Solubility: Easily soluble || Easily soluble Shelf Life: 180 days || 180 days Application SERIBOND FILLEX can be used in all kinds of writing & printing paper, duplex boards, Kraft paper ect. It may be used after addition of resin and best addition point is mixing chest. The recommended dosage of SERIBOND FILLEX is 0.20% to 0.60% on dry paper basis to get the desired result. Packing: 200 Kgs Carboys and 200 Kgs. Drums Storage & Handling: Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND–WSR–1830 SERIBOND–WSR–1830 resin is a unique chemistry. This versatile product is specially designed to perform critical tasks in towel, napkin and facial grades. Promotion or improved retention of polyamide wet strength resin Enhancement of Functional performance of the sheet with higher wet strength, dry strength, and improved Wet-Over-Dry Restoring Wet End Charge Balance, especially on machines that run close to or in the cationic range Specification Appearance: Liquid, clear to slightly hazy Solid: 29 – 30 % Density: 1.05 g/cm3 Viscosity @ 250C: 2,300 – 6,300 cps PH Value: 3 – 3.5 Ionic nature: cationic Solubility: Easily soluble in water Application SERIBOND–WSR–1830 resin is designed to be added after the polyamide wet strength resin at a point of good mixing. It is important that the SERIBOND–WSR–1830 resin is thoroughly mixed with the stock. Addition of SERIBOND– WSR–1830 to either the thin or thick stock is acceptable, depending upon the polyamide wet strength resin and other cationic additives dosage points and program objective. Typical dosage level for the SERIBOND–WSR–1830 is 0.05 to 0.1 % on fiber, dry solids basis. Packing:200 Kgs Drums Storage & Handling:Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND–WSR–1825 SERIBOND–WSR–1825 resin is a unique chemistry. This versatile product is specially designed to perform critical tasks in towel, napkin and facial grades. Promotion or improved retention of polyamide wet strength resin Enhancement of Functional performance of the sheet with higher wet strength, dry strength, and improved Wet-Over-Dry Restoring Wet End Charge Balance, especially on machines that run close to or in the cationic range Specification Appearance: Liquid, clear to slightly hazy Solid: 25 – 26 % Density: 1.05 g/cm3 Viscosity @ 250C: 2,300 – 6,300 cps PH Value: 3 – 3.5 Ionic nature: cationic Solubility: Easily soluble in water Application SERIBOND–WSR–1825 resin is designed to be added after the polyamide wet strength resin at a point of good mixing. It is important that the SERIBOND–WSR–1825 resin is thoroughly mixed with the stock. Addition of SERIBOND–WSR–1825 to either the thin or thick stock is acceptable, depending upon the polyamide wet strength resin and other cationic additives dosage points and program objective. Typical dosage level for the SERIBOND–WSR–1825 is 0.05 to 0.1 % on fiber, dry solids basis. Packing:200 Kgs Drums Storage & Handling:Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND–WSR–1815 SERIBOND–WSR–1815 resin is a unique chemistry. This versatile product is specially designed to perform critical tasks in towel, napkin and facial grades. Promotion or improved retention of polyamide wet strength resin Enhancement of Functional performance of the sheet with higher wet strength, dry strength, and improved Wet-Over-Dry Restoring Wet End Charge Balance, especially on machines that run close to or in the cationic range Specification Appearance: Liquid, clear to slightly hazy Solid: 14 – 15 % Density: 1.05 g/cm3 Viscosity @ 250C: 2,300 – 6,300 cps PH Value: 4.7 – 5.2 Ionic nature: cationic Solubility: Easily soluble in water Application SERIBOND–WSR–1815 resin is designed to be added after the polyamide wet strength resin at a point of good mixing. It is important that the PAE resin is thoroughly mixed with the stock prior to the addition of the SERIBOND–WSR–1815 resin. Addition of SERIBOND–WSR–1815 to either the thin or thick stock is acceptable, depending upon the polyamide wet strength resin and other cationic additives dosage points and program objective. Typical dosage level for the SERIBOND–WSR–1815 is 0.1-0.2% on fiber, dry solids basis. Packing: 200 Kgs Drums Storage & Handling: Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND-DSR (CATIONIC) SERIBOND-DSR (CATIONIC) is excellent dry strength resin for paper Industry. It is most suitable product for short fiber pulp like Bagasse, Straw, Waste paper, Bamboo, hard wood etc. It also improves strength properties like brust factor, stiffness, breaking length, ply bonding, tear factor of Kraft, Duplex Board and writing and printing paper, SERIBOND-DSR (CATIONIC) gives better sheet formation and also increase machine run ability. It improves retention of fillers & fines and eliminate press picking problem of paper. Specification Appearance: Clear Water Colour Solid: 15 ± 1 Viscosity on Brook Field cps: 3000-6000 PH Value: 4 ± 1 Ionic nature: High Cationic Composition: Acrylic based polymer Solubility: Easily soluble in water Shelf Life: 180 days. Application SERIBOND-DSR (CATIONIC) can be used in all kinds of writing & printing. Duplex boards, Kraft paper. It may be used after addition of rosin and best addition point is mixing chest Before addition of SERIBOND-DSR (CATIONIC) it should be diluted to -10% to -20% solution. For Duplex board addition point is protective and bottom layer. The recommended dosage of SERIBOND-DSR (CATIONIC) is 0.20% to 0.60% on dry paper basis to get the desired result. Packing: 200 Kgs Carboys and 200 Kgs. Drums Storage & Handling: Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND-DSR (ANIONIC) SERIBOND-DSR (ANIONIC) is excellent dry strength resin for paper Industry. It is most suitable product for short fiber pulp like Bagasse, Straw, Waste paper, Bamboo, hard wood etc. It also improves strength properties like brust factor, stiffness, breaking length, ply bonding, tear factor of Kraft, Duplex Board and writing and printing paper, SERIBOND-DSR (ANIONIC) gives better sheet formation and also increase machine run ability. It improves retention of fillers & fines and eliminate press picking problem of paper. Specification Appearance: Clear Water Colour Solid: 20 ± 1 Viscosity on Brook Field cps: 3000-6000 PH Value: 4 ± 1 Ionic nature: High Anionic Composition: Acrylic based polymer Solubility: Easily soluble in water Shelf Life: 180 days. Application SERIBOND-DSR (ANIONIC) can be used in all kinds of writing & printing. Duplex boards, Kraft paper. It may be used after addition of rosin and best addition point is mixing chest Before addition of SERIBOND-DSR (ANIONIC) it should be diluted to -10% to -20% solution. For Duplex board addition point is protective and bottom layer. The recommended dosage of SERIBOND-DSR (ANIONIC) is 0.20% to 0.60% on dry paper basis to get the desired result. Packing: 200 Kgs Carboys and 200 Kgs. Drums Storage & Handling: Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND-ANTIFORM-VO SERIBOND-ANTIFORM-VO is a revolutionary antifoam formulation dedicated for paper making. It is a very effective defoamer and paper stock deaerator. It is suitable for multiple applications such as waste water treatment, oil drilling etc It is recommended to treat aqueous foam problems. Aqueous emulsion of organic hydroxy compounds, fatty acid esters and surfactants. APEO free. Benifis 1) SERIBOND-ANTIFORM-VO is very persistent and shows excellent performance in the control of foams by significantly reducing the entrained air content. 2) It is does not affect sizing or paper strength. 3) It is very effective even at low concentrations and facilitates smoother pump operation, transport. 4) Leaves no residues in the pipes or valves of the equipment used. Specification Appearance: Milky flowable emulsion Solid: 50 % Specific gravity at 25 ºC approx. 1.00 g/cm3 Shelf Life: 180 days. Application SERIBOND-ANTIFORM-VO Apply the product in its natural state by aspersion or by dosing pump and adjust the initial dosage according to the requirements. SERIBOND-ANTIFORM-VO may also be distributed with a water dilution system and or with a special metering system for automatic dosing, which means product will automatically added only when needed. Packing:200 Kgs Carboys and 200 Kgs. Drums Storage & Handling Stir well before use. Store at room temperature in original closed containers. The minimum shelf life in closed containers is 12 months from the date of manufacture. Mix product and retest for quality after one year from the date of manufacture. Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
SERIBOND-ANTIFORM-E SERIBOND-ANTIFORM-E is a revolutionary antifoam formulation dedicated for paper making. It is a very effective defoamer and paper stock deaerator. It is suitable for multiple applications such as waste water treatment, oil drilling etc It is recommended to treat aqueous foam problems. Aqueous emulsion of organic hydroxy compounds, fatty acid esters and surfactants. APEO free. Benifis 1) SERIBOND-ANTIFORM-E is very persistent and shows excellent performance in the control of foams by significantly reducing the entrained air content. 2) It is does not affect sizing or paper strength. 3) It is very effective even at low concentrations and facilitates smoother pump operation, transport. 4) Leaves no residues in the pipes or valves of the equipment used Specification Appearance: Milky flowable emulsion Solid: 29 % Specific gravity at 25 ºC approx. 1.00 g/cm3 Shelf Life: 180 days. Application SERIBOND-ANTIFORM-E Apply the product in its natural state by aspersion or by dosing pump and adjust the initial dosage according to the requirements. SERIBOND-ANTIFORM-E may also be distributed with a water dilution system and or with a special metering system for automatic dosing, which means product will automatically added only when needed. Packing:200 Kgs Carboys and 200 Kgs. Drums Storage & Handling Stir well before use. Store at room temperature in original closed containers. The minimum shelf life in closed containers is 12 months from the date of manufacture. Mix product and retest for quality after one year from the date of manufacture. Storage must be in covered place. Carboys should be kept tightly closed when not in use. Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers, consult Material Safety Data Sheets and follow all local or national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take precautions against possible risks of fire or explosions as well as protection of the environment. Apply only in well ventilated areas. Disclaimer: The information in this document is given to the best of Serix’s knowledge, based on laboratory testing and practical experience. Serix’s product are considered as semi-finished goods and as such products are often used under conditions beyond Serix’s control. Serix cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements. Serix reserves the right to change the given data without further notice. Users should always consult Serix for specific guidance on the general suitability of this product for their needs and specific application practices
